Hacker News new | past | comments | ask | show | jobs | submit login
My cat water fountain comes with a spicy USB power adapter (ounapuu.ee)
336 points by hddherman 11 months ago | hide | past | favorite | 303 comments



Lidl does this too – the rotary tool Parkside PFBS 12 B3 comes with a charger that's obviously not USB-PD, but has an USB-C plug and it puts out a solid 13 volts at all times. (See https://www.kompernass.com/en/accessories/2316/charger-8 for an image.)

I sent Lidl a courteous and long mail about this and they didn't really care other than "please open a service ticket with your local Lidl", which I didn't care to do since what would they do?


> courteous and long

How about urgent and short?

e.g. One day a kid will charge their toy over night with your 13v usb-c charger and they'll burn their house down.


Just a little too short, add:

“and this email notification demonstrates you are aware of the hazard which will be relevant in lawsuits.”


and they will respond with "We sincerely thank you for your concern. We have a 6 month email retention policy in place to address your issue"


In recognition of your email retention policy, I shall be resending this complaint at 5 month intervals, along with a running history of the previous complaints.


Hypothetically, and just out of curiosity: if mint2 were to keep this email and it would be included as part of the evidence in a lawsuit, how would this bode for Lidl?


Assuming it wasn't mint2 that had the fire, it would almost surely go undetected in discovery. (Lidl would say "as required, we've searched for and provided all emails and care contacts referencing USB chargers".)


If you can't add anything useful, stay out.

Although I wonder if it was your house to burn down whether you might feel a little differently about doing the right thing.

The answer is, you CC trading standards(Or your country's equivalent) as well.


What makes you think I have negative opinions about doing the right thing, or my comments aren't useful.

Perhaps CCing trading standards is actually a good idea, and Im glad I raised a valid concern about the utility of emailing the supplier alone.


It didn't appear constructive, just implying that they were going to do their best to lose the email.

Here in the UK it's quite easy to get stuff fixed. A few years ago, a single complaint to trading standards by me got a can relabelled properly with its ingredients. Failing that, I know from prior experience that companies hate being embarrassed. They really value their image, and risking house fires for your consumers, it doesn't go down well.

What you posted came across as negative, and I'm afraid I have a fairly low tolerance for that. If I misread you, sorry.


I agree that it is a lot easier to do a drive by shoot down of someone else's idea than provide a constructive solution. That has to be balanced with the idea that a dose of realism is necessary for improvement and iteration.

As such, I don't think negative is always bad.


I’m really interested in which can you got relabelled! Could you disclose it?


I didn't directly mention burning down the house, but I did say

"The takeaway of this is that given the plug looks exactly like a standard USB-C phone charger's plug, it's easy for a novice user (say, a child whose phone charger's wire has been bit through by the family dog) to attempt to charge a device not rated for 13 V using this charger, which is quite likely to damage the device."


I have the same tool and charger and only noticed the out-of-spec voltage after trying to charge the tool with a regular USB-C cable and charger. It's really disappointing someone thought this is a good design.

Newer revisions of the tool don't seem to have this flaw though. They only come with a USB-C cable and no charger in the box.

Also thanks for reminding me to put a big sticker on the charger with a warning!


So instead of a barrel plug, they ... made a barrel plug shaped like a USB-C connector?


Is there any EU body you can report them to?


Well, i had the same question and looking for this & the rules in general was... lets call it "a fun evening".

Those common charger EU rules pushing USB-C via the Radio Equipment Directive are actually only for the device, and even a specific list of types. But in briefing document [2] (made for RED change last year) mentions:

> a separate initiative on the eco-design for the external power supply (EPS) would harmonise the EPS-side receptacle and the communication protocol.

So "EPS" is what we are looking for and they use some eco laws to regulate them. [1] gives an overview and links COMMISSION REGULATION (EU) 2019/1782. And again, it only applies to a specific set of devices, with power tools not being listed. Doubt those fall under "Other toys, leisure and sports equipment"^^

Back to that EPS initiative... from my understanding, it [3] seems to be still "Planned for Third quarter 2023". Feedback period ended in May 2022, ofc.

The department seems to have vacant spot [4] for an expert, btw :)

[1] https://commission.europa.eu/energy-climate-change-environme... [2] https://www.europarl.europa.eu/RegData/etudes/BRIE/2021/6988... [3] https://ec.europa.eu/info/law/better-regulation/have-your-sa... [4] https://www.cnr.it/sites/default/files/public/media/internaz...


Like those self-installed USB-chargers that are directly connected to your car battery. Can work sometimes, but you need robust devices.

Probably a side effect when USB-PD was introduced and people neglected the facts that there needs to be an elaborate handshake for anything other than 5V.

Previously we always needed to check non-USB chargers for their voltage and there were connectors and adapters for different sizes. But now you need to be more careful with USB as well.


Report them to trading standards.


> long

People don't like to read. Short & concise wins the day here.


As much as people hate on the EU, this is their sort of jam, EU should ban misuse of things like USB. Bam, problem solved. They even sorted out "we wer alwuz planin 2 use USB c, it wuz our plan all alung" Apple.


9v or 12v over USB-A is reasonably common here in Asia... You always need to check the voltage rating before randomly plugging stuff in if it isn't from a big manufacturer.

For example, the handwarmers I'm using right now are USB-A at 12 volts, but have a dial to adjust the voltage up and down between 0 volts and 12 volts to adjust the temperature (I think it's actually PWM on the 12v power lines, but haven't actually checked).

5.5V or 6V is also common because it lets you use thin cheap wires which remove about a volt and still can fast charge phones (which tend to be picky and will drop back to 500mA charging if the voltage droops).

Big manufacturers also use non-5V over USB sometimes, but you need to send a special message to enable higher voltages, so it's safe to plug them into anything. Still troublesome if you're using a USB Y-splitter or multi-headeded cable.


Where in Asia? I lived in China from 2010 to 2019 and the only voltages I've seen on USB A ports is ~5V and ~4.2V. The latter on the charger for some rechargable bicycle lights.


Thailand


> Thailand

> USB-powered handwarmers

This combination is just weird. So weird, that the only place I can think this then applies, is... Thailand.


Tourists only go to the beach areas, north has mountains and can be quite cold


I know (I have family there, and near the beaches).

But "cold" is relative. I've had temps as low as 14℃ (57F) in Chiang Rai, Pai and near Udon Thani. And while that may be "freezing" to people used to tropical climates, that's shorts-and-terrace-outdoor-yay temps where I'm from (North Western Europe).

I found it alienating to see people with woolen hats, mittens, thick jackets and scarves in Thailand, when for me the temps were T-Shirt and shorts grade.

edit: Though, reversed, another alienating sight was a kiosk with Thai Takeaway on a parking lot in Åre ("north-Sweden, south-lapland) under 2m snow and ice with outside temps of -18℃.


That’s terrible. Why don’t they just use a barrel plug?


Not that barrel plugs are any better...

I wish I would have wrote the model down posterity, but at one point I worked a trading company and a number of the users had ISDN at home. There were two 'different' modems, and I say different because only the model number on them notified you of it.

One had a plug that output DC power. One had a plug that output AC power.

They were the same size wall wart. Same size barrel. But if you plugged the AC adapter in to the DC modem it would make a noise like you curled the modem up into a ball and let the magic smoke out.


Barrel plugs are not better technically, but it would be better to use them with random voltages because people don't assume that they conform to a standard. With barrel plugs, the customer expectation is that every device has its own charger, and that's that. With USB, the assumption is that they are all compatible.


With barrel plugs the likelyhood that one of your devices will have one that fits into another is basically zero too.


I keep power supplies around when the device they were supposed to power goes out of service. The collection has grown to a big crate of assorted power supplies where I can hunt for a spare. It is common that I have to solder on a plug from another power supply, but it's not rare to find multiple compatible supplies that have the right plug and specs.

The scenario you describe, where I'm looking for a power supply among a set of devices, to power another device, that is less likely to turn up a winner. But chances are non-zero enough that I do wander around looking for other options when a power supply is missing.


I have found this not be true too often. Then again maybe I have more computing junk than most.

Really it should be a manufacture requirement that the barrel port on the device have a waterproof hard to destroy sticker, or case moulding that lists it's requirements. As the years have gone by I've seen way too many devices with a plug hole and no idea what it thirsts for, leading to deep searches on the net for the product. Also the wall warts themselves are commonly made by some other group, so once separated there is little to no visible pairing identification other than looking for output/input power on both devices.


I've recently made a habit of labeling power adapters with the device it belongs to. Too often I have wanted to use an old device I have not used for a few years, then had to go through my box of old power adapters trying to match up the plug, voltage, and current to the device in hand.


Barrel connectors come in standard sizes and usually have the voltage rating on the device.


I mean they are multiple sizes but there are certainly standards. When they were more common I use to have boxes of them and could always find barrels to fit anything I needed and swap over the power supply to match whatever power I needed. Once in awhile you would get lucky and have both a matching plug and supply to match your need, like my electric piano uses my old Sega Genesis wall wart and plug because they matched voltage and barrel plug size and a cat chewed the original piano one and cause it to short and burn out.


Semi-related: My wife has the little Fallout 4 fridge they dropped a while back, not a proper fridge but one of those peltier plate ones that's only really good for like, soda and beer. She was quite upset when it died one day and I toss it on the bench, and stab the power socket with my alligator clips and give it 9 volts. Worked perfectly so it just needed a new power supply.

A quick Amazon order, snip the wire off the old, splice it to the new and a little soldering/heatshrink later and we're back in business. Plug it in and... nothing. Turns out, the original power supply had it's polarity reversed. So then I opened the fridge and swapped the connections on the backside of the socket because it was less fuck-about than re-splicing the wire. Fortunately a few confused minutes of reversed polarity didn't damage anything (not that there's really anything to damage, it's a peltier plate and a fan)

Genuinely, why? The standards make things easier. Why go out of your way to not use them?


> Turns out, the original power supply had it's polarity reversed.

Doesn't that make it a heater, instead of doing nothing?


Nah, the machine was just wired entirely backwards. The +9V off the power supply was connected to 0V inside, and was in fact acting as the 0V with the other delivering the +9V. The wires were marked on the power cable, and were just backwards, so when I snipped and spliced on a new power supply with the polarity correct, it was then reversed inside.


One had a plug that output DC power. One had a plug that output AC power.

Oh, man, that reminds me of how I found out that MicroLogix PLCs[0] come in AC flavors and DC flavors. So the MicroLogix 1400 I had lying around here used an AC adapter, and you screwed the stripped wires into the holes that used screw retainers. Easy-peasy, just make sure the adapter's not plugged in in you wire it up. The boss orders me another MicroLogix 1400 for long-forgotten reasons, and to get it bootstrapped, I decided to use the adapter from the other 1400.

I already gave away the plot in the first sentence, and you can guess what happened next.

[0] https://en.wikipedia.org/wiki/Programmable_logic_controller


Barrel plugs ARE better because there is very little certainty about them so you always have to check the voltages/polarity. Because usb-a is near ubiquitously 5v over certain pins most people will plug in a usb-a into any socket they see.


It's the designated dumpster fire "Lol you're on your own" plug!

Probably the best connector we've got for things that need it, but I'm glad we have USB-PD power now


That's kind of my point. There is no standard at all with barrel connectors, usually bigger connectors means more watts but not even that is true as a rule of thumb.

When you see a barrel connector all the following things are true:

1) no voltage can be inferred

2) no amperage can be inferred

3) Not even the polarity can be inferred

You must check the device and the wart for all that information.


Because it's cheap and easy to implement into designs. No need to spec and use a new part, just use USB-A for all power connections across everything you sell.


There's lots of those too - and converters from USB to barrel (of various sizes) and vice versa.

The only thing that is truly standard is the polarity of power on a USB-A plug.


Because the EU banned barrel connectors.


This is absolutely cursed.


I have/had this cat water fountain too (my cats are now happy with a normal bowl) and I believe I just threw the wall wart into a box with the rest of my unused USB A wall warts. A little bit like electrical Russian roulette now, I guess.


I couldn’t get mine to drink from it. They side-eyed it warily and avoided my attempts to entice them.

Cats.


Bought my cat a nice and large bed which is more akin to a throne but anyway. He now happily sleeps directly next to it.


The level of interest a cat exhibits in a toy is inversely proportional to its price.

Unless it's something you bought for yourself rather than the cat, in which case the cat goes for the most expensive thing first.


Fully subscribe to this take.

But in all seriousness, I think I underestimated just how much cats rely on smell at all times. I noticed yesterday that this plushy polyester bed is still strongly smelling like plastic mixed with some random pet store odors. This is likely not helping.

I will laundry it at 60 degrees Celsius as recommended, sprinkle some of his cat hair around it and then see if he finally accepts it. At the moment he still prefers sleep on (multiple) electronic devices and on the floor in the hallway between rooms (attacking anyone passing by).


There are a couple of them which offer selectable force of the fountain effect (e.g. https://www.chewy.com/petlibro-stainless-steel-dog-cat/dp/37...), so it may be their domestication has tamped down the "babbling stream" identification circuits and they need something a little softer

I'd also be on the lookout for the electrical hum mentioned in TFA; that would drive me crazy, and I can't speak to how it would make any kitty wary

Also, and this may go without saying, but watch out for the fountain(s) being made out of materials which are hard to clean


I was once working on an app for a Clover point of sale system. On the side there is a USB-C port. I plugged my new-ish MacBook Pro into it thinking I would be able to debug, but instead my mac instantly went black. I unplugged it, and eventually it rebooted, but the USB ports on that side never worked again.

Turns out that port is intended for connecting a receipt printer, and clearly not in any way a standard USB-C.

There is actually a micro usb port elsewhere on the device that can be used for debugging. Lesson learned the hard way.


"Model 3.0, now with integrated USB-KILL"


I am concerned that there are no pictures of the adorable cats in the post.

It sound like the manufacturers just see USB-A as a convenient and cheap connector for delivering power.


Hi, author here, I've fixed that in the post now.


Your cats are adopting the universally understood pose of their human not being on time to feed them.


Great news!

By the way, are you Finnish? I've never seen an 'O with tilde' character before.


Nope, Estonian. Quite close to Finnish but not quite the same. We do have all the õäöü-s that we need though.


I apparently need to map more. My head had some Mercator perversion where Finland and Estonia were a continent apart. Or maybe I don't do spheres well.


Vietnamese uses the O with tilde charcater Õ, it's fairly common.

The first word I can think of is ngõ

https://en.wiktionary.org/wiki/ng%C3%B5_h%E1%BA%BBm


A Møøse once bit my sister...


https://en.wikipedia.org/wiki/%C3%95

It's a pretty rare character indeed.


Amazing, they are indeed adorable!


Adorable review approved


>It sound like the manufacturers just see USB-A as a convenient and cheap connector for delivering power.

Is it really any cheaper than a simple barrel connector that manufacturers have used forever for power?


Probably cheaper by half a cent.


This actually makes me quite happy that most stuff does not come with a wall adapter anymore these days, but only with a USB plug.

There are much worse things than 7V that a bad adapter can output.

One of the scariest failure modes I’ve recently learned about is a supply that still provides 5V between both pins – but 225V and 230V to ground, respectively…


I just bought the one from Eufy and it didn't come with a wall wart. I used the wart that came with a lamp. The lamps is plugged to the USB port on my sit-stand-desk.

When I raise and lower the desk, the lamp lights up. That might not be the power port, it may be the "induction" power button on the lamp's chord getting interference from the desk motors. I'm living the tinderbox life.


> respectively

not sure I follow you. can you clarify what you mean by both 225v and 230v to ground? You are measuring the potential between ground and USB output?


There are two pins. One has 225V to ground, the other one has 230V to ground. So the voltage from pin to pin is still 230V-225V = 5V.


Yes, and given that USB devices usually don’t have protective grounding (since they expect to be supplied 5V to ground at most!), you just might be what eventually provides that ground connection when you touch a conducting part of the case…


Surely this is a violation of the specifications?


Definitely at least electrical standards in most countries, and probably USB also specifies that the voltage needs to be isolated from mains.

But yeah, usually those are illegal to be sold.


I thought he was going to say there was current in the water.

I remember showering in Costa Rica at a “hotel” and the shower head was one of those that heats the water (with an electric heater) and it was shocking me the whole time I used it. Probably shouldn’t have used it

Apparently those are common in central and South America.


I remember this video [1] from bigclive about it. I had no idea it was so common to have live wires in contact with water. At least they are grounded sometimes?

[1] https://www.youtube.com/watch?v=cNjA0aee07k


Sometimes. In my experience in living in 3rd world it’s more like extremely rarely. The tingle just lets you know it’s working.


Yup. When traveling abroad in a developing nation it turns out no one bothers to ground their power, so my macbooks (or my friend's laptop) always shocks me if I touch it while plugging in. You kinda taste iron if you keep touching it, but all the locals are used to it.


In developed countries they do the same if you use the duck head on the adaptor instead of the cable with the grounded connector sadly.

And yes it's because of the metal case. It's not the actual mains you're connected to though, just some induction on the PSU shielding.


The only laptops I've seen doing that are Apple laptops, for some reason other laptop brands do not seem to have that problem.


It's the metal case. Most PCs are plastic


it's happened on my friend's laptop and other non-macs laptops too


> The idea of a water fountain for cats may sound odd

Cats instinctively love & trust moving water as stagnant water can accumulate bacteria & disease.

So a cat fountain sounds like a gimmick or novelty but it’s a great idea.


I bet my cat drinks 500% more water since getting him this fountain, as compared to a still bowl of water.

It’s cute and adorable (the fountain is a bit silly looking), and I have to assume it’s good for him.

And to guard against power outages, I got him a separate fountain with an open top, so in a pinch at least he had some standing water.


I got one after I noticed how much my cat liked to jump up to the sink and try to drink from the tap while I was using it. He loves it, and anecdotally seems to drink more than he did without.


One of my cats learned to bump the faucet lever on the kitchen sink when he wanted a drink. Fortunately the sink only overflowed twice but that was enough to make me very serious about not leaving dishes in the sink.


Ours love direct from tap,but assumes the fountain is going to kill them.


Same here, we like our own furniture and faucets.

So the cats have their own cat towers and a water fountain. The first day with the fountain, the cats were so chill. I wonder if running-water sound soothes them.


Yeah I though ti was weird and was skeptical the first time I saw one. Ended up getting one later and the cats love it.


I have the same fountains and I have already roasted an iPad charger on it fountain (I used the charger because it had possibility to connect cable to it instead of plugin directly to the socket). One day it just went out and burnt a little.

From that time I tend to use the provided one, but I never noticed it provides a different voltage. Thanks for the warning


An official Apple iPad charger wouldn't fail in this case - it has protection against basically anything on the output side - from short circuits to big back-EMF spikes.

3rd party ones on the other hand....


This is the reason I only use apple chargers for charging everything.


There are much higher quality chargers (and cables) than Apple's.

Anker is well known, and Baseus is getting there. They are especially nice because they make GaN chargers, putting a lot of power in a tiny package.

It honestly kind of baffles me how crappy Apple's cables and chargers are when they simultaneously make one of the best USB-C to 3.5mm DACs on the market, and then sell it for $10.


Are they as high quality? I’ve seen the Apple charging hardware breakdowns and they pack a ton of stuff in there.


Anker has been surprisingly good. I worried they were a Chinese faux brand but everything I’ve gotten has been solid and well made.


The Chinese are definitely capable of producing great products, it's just that the quality control for that is only there for name- / high-end- / West-controlled brands.

I believe the Chinese government is keen to get rid of the crappy reputation Chinese products carry ("Chinesium"), but its gonna be a process.


I recently got a 67W PD changer from Toocki on AliExpress, it actually delivers enough power to charge my laptop (via a USB-C to barrel jack adapter) reliably, and for 12$

I originally thought there was no way these work as advertised, but I saw a guy I know using one to charge his laptop, and he has the engineering knowledge to properly test it so I decided to go with his recommendation


My anecdote is that Baseus adapter seems to broke my AirPods. Anker is now considered to the best charger brand available in the market.


I saw a device (a drill or something) that had a standard USB-C plug on it's charger. I thought - nice, I can charge a drill with my PD charger or use it's charger to charge my phone while I'm in the garage!

But the charger was always giving 12 or even 20V (i don't remember exactly, I don't have access to this device now).

A real trap.


Really informative article thanks, however, I think that "my two adorable cats" should have a link to the two adorable cats.


You did it!!


Increased voltage in itself is okay if done through any of the negotiated power delivery standards such as USB PD

Latest USB PD supports up to 48V and up to 5A, resulting in 240W

That’s also a reason why not all fast chargers work well for all products – if the required voltage + amperage combination is not supported then the closest supported lower combination will be used instead.

That said, 7.5 volt is not a supported voltage in USB PD at least and there seems to be no handshake that guards it in this case


This is the sort of thing that almost (but not quite) pushes me to support mandatory certification (enforced by patents/other IP protections) for consumer devices that use a familiar connector like USB.

Consumers shouldn’t need to worry about the specific output voltage; the presence of a USB-A connector should indicate that it abides by the specification.

The hacker in me hates the idea of enforcing something like this, but poor interoperability is such a pain that it would be nice to have stronger guarantees.


I think when it comes to safety restrictions should be there. The hacker in me hates it too but just imagine if a small portion of standard-looking outlets did not output 220V (or whatever standard you have) and say 330V.

Many applicances would break, or perhaps even catch fire.

If there were many different USB-A devices and people were used to checking the voltage output before plugging, that might not be needed, but since probably none of us check for a USB-A port to see if it outputs 7.5V, it better be mandatory to be certified.

Though, maybe it is, but still those cheap Chinese adapters slip away.


> just imagine if a small portion of standard-looking outlets did not output 220V (or whatever standard you have) and say 330V.

We have something like that here in Brazil. On cities which use 127V as the standard voltage (some cities use 220V), you can get 220V by using a pair of phases instead of a phase and the neutral, and it's common to find a few standard-looking sockets which are 220V instead of 127V. They might be colored red, they might have a yellow sticker saying "220V" next to it, or they might be completely unmarked. If your device is 127V only, or it has a manual 127V/220V switch which is on the 127V position, and you plug it into one of these 220V sockets, it will be damaged.

(The standard we use for consumer AC power plugs and sockets, NBR 14136, does not make a distinction between voltages; the same plugs and sockets are used for both 127V and 220V.)


That sounds incredibly error prone and actually quite dangerous! At least a lot of AC to DC converters are universal voltage and frequency, but not all appliances!

In Australia we have only one voltage that will ever come out of a single phase socket, but the standards took the opposite approach with current ratings - the sockets are cleverly designed in terms of their current capacity so (assuming it’s been installed correctly) you can’t make mistakes without illegal and dangerous modifications. In the standard socket, you can have 10 amp, 15 amp or 20 amp, and they all have different sized pins. For the 15 amp plug and socket, the ground pin is larger, so a 15 amp plug cannot fit into a 10 amp socket. A 20 amp plug has all three pins larger, so it doesn’t fit in a 10 amp or 15 amp socket. But a 10 amp plug can still fit and sit snugly in a 15 or 20 amp socket, and a 15 amp can still fit into a 20 amp socket with no problems. It’s pretty clever.

For bigger stuff, or anything three-phase, you then have big industrial circular ones, which I think have a similar system to not let you plug a higher current device into a socket that can’t supply enough current. I believe there are also three phase plugs and sockets both with neutral and without neutral, and if the plug has a neutral pin it doesn’t fit into a socket that doesn’t supply neutral.


> But a 10 amp plug can still fit and sit snugly in a 15 or 20 amp socket, and a 15 amp can still fit into a 20 amp socket with no problems. It’s pretty clever.

That sound dangerous. The larger fuse sized for the 20A socket will not protect the smaller conductors in the cable sized for the 10A plug, they can get overloaded.

The three-phase / industrial CEE plugs and sockets used in the EU are sized for 16A/32A/63A/125A. It's perfectly legal and safe to make a passive adapter that lets you plug a 32A appliance or distribution box into a 16A socket, you just can't load it higher than the 16A fuses on the socket. Going the other way around (16A plug into a 32A socket) you MUST have a circuit breaker in between to provide the required overload protection.


That doesn't make sense though. The fuses aren't to protect the load; they are to protect the circuit. It's up to whatever device you are plugging in to not draw more current than it can handle.

If I have a 3 Watt doohickey, I don't go looking around to find a 0.025A socket, I plug it in to my 15A wall socket and everything works great.


Yeah, the risks mainly come with extension cords, like plugging a bunch of 10A appliances into a single 20A outlet via a 10A rated extension cord with multiple 10A outlets.

Appliances themselves with their own input fuses and captive cables are less risky, although some kind of internal wiring short could still get all melty.

It's true that sizing the plugs that way does prevent you from plugging a 20A appliance into a 10A extension cord, which makes sense.


Each individual socket isn’t fused though. The entire circuit is. The fuse(breaker) is going to be significantly bigger than any of those amperages.

The breaker is there to protect the wiring in the building, nothing more. It’s spec’d to the gauge of the cable in the wall typically.


It's not dangerous in practice. Reading through NEC in the US, there's plenty of leeway for mixing ampacity ratings on circuits, within certain limits. For example, it's fine to have 10x 15A duplex on a 20A circuit. It results in less wiring, and allows for logical grouping of circuits. Electrical code starts from the the most common causes of electrical failures, and tries to design down from there. The ampacity ratings on devices and various components of the circuit are designed to reject the common causes of failure, and conductor failure at the device isn't one of them (appliance manufacturers are more likely to get their devices certified, so if there's a failure in the appliance, some other part of the appliance's electrical system will fail before the conductors do).

So the ampacity of the connector (duplex and plug) is meant to reject certain combinations (plugging a 30amp appliance into a 15amp duplex/circuit). It's obviously very easy to get around that by just wiring things together wrong (18AWG wire on a 30Amp circuit), but by design, a 30amp appliance with the proper plug cannot be plugged into a 15amp outlet.

Of course, this is informed by the electrical code in my home country, so I understand that other places and people have different experiences, but electrical accidents have been on a steady downward trend since the 80's, so the NFPA NEC has to be doing at least some things right.


It is indeed very regional, e.g. the UK has its own thing going on with ring mains and fused plugs.

Over in my 230V corner of the EU, CEE 7/3 sockets are pretty much the only thing I'm aware of for new wiring, with the unearthed CEE 7/1 sockets still present in older installations. Both are rated for 16A, with either 10A/1.5mm² or 16A/2.5mm² branch circuits from the distribution board. It would be unheard of to wire those up with any higher ampacity at risk of overloading the sockets - although recent experience with e.g. EVs has shown that they're not actually suitable for sustained loads at 16A, given e.g. wear and tear on the sockets.

Unearthed appliances do commonly have CEE 7/16 plugs rated for 2.5A, particularly things like wall warts or USB chargers, which does fit into a CEE 7/3 socket.

I recall seeing CEE 7/16 (2.5A europlug) sockets, although those may have been imports from elsewhere in the EU. I suppose those would have the same issues if wired up to the same distribution circuits. But extension cables for those are rarer, the only ones I've ever seen are CEE 7/7 plug (16A) -> CEE 7/16 sockets (2.5A).

For residential/commercial loads over 16A / 3.2kW, it's all CEE / IEC 60309 connectors, and those are treated like distribution circuits with overload protection sized appropriately for the connectors/cables.


Is "ampacity" really a better word than "current"? And the unit symbol is just "A", like "30 A".

I realize I'm nitty but this is a technical-minded forum after all.


"ampacity" means "capacity in amperes" or more literally "ampere capacity." You could say current capacity too but it takes longer. Ampacity is the language used in the electrical code.

"amp" also seems to be more common to write than "A" for electricians. Remember that the SI standardization of unit abbreviations is actually a pretty modern thing, so lots of fields existed before unit abbreviations were standardized and continue to use existing practices.


Ah I did not get that meaning, then obviously it's a perfectly cromulent word. Thanks and TIL.


Nah, it's fine to be nitty. If you glance at my comment again, you'll see my usage devolve from A to amp halfway through, my brain can't help but write what it sounds like to me.

Yes though, ampacity is the correct word (for my home country). "Current" is an instantaneous measurement of current flow. That they use the same unit is pretty convenient for planning circuits. https://en.wikipedia.org/wiki/Ampacity#:~:text=Ampacity%20is....


> In the standard socket, you can have 10 amp, 15 amp or 20 amp, and they all have different sized pins.

Yeah, Brazilian NBR 14136 does that too. It has 10A and 20A variants, and the only difference is that 20A has slightly larger pins, so it won't fit into a 10A socket. (And the international standard it was based on, IEC 60906-1, has only a 16A variant with an intermediate pin size, so the 10A plug would fit into its socket and its plug would fit into the 20A socket.) Annoyingly, that's the only difference, making it quite hard to tell just by looking whether it's a 10A or 20A plug/socket; you have to try and see if it fits.


Brazil should use outlets to indicate the voltage. With Type A for 127V, the worldwide standard for 120V plugs. Then Type N for 220V, where there is no standard but Type N is pretty good design. Changing outlets is pretty easy to do.


> With Type A for 127V, the worldwide standard for 120V plugs.

That would be going backwards, and losing all the safety features of the new NBR 14136 ("type N") standard; to make it worse, we already did use something like "type A" (with "universal" sockets which accepted both flat and round pins, and sometimes even grounded "type B" together with these two, it was a mess) for both 127V and 220V, so you'd still have (in older buildings) these "type A" plugs being used for 220V.


In my old house (US) there was an outlet that was setup that way. Two phases plus ground on a bog standard looking 120V outlet. Made the discovery when we plugged a 500W work light into it while renovating and it exploded after a few minutes.


So you had a glorious 2kW work light for a few minutes.


"The candle that burns twice as bright, burns half as long"

The math was a little off, but the quote still comes to mind


Yeah, the wiring code says the 220V outlets on 110V areas must be red. Marking is optional.

But I've actually have never seen a red one.


That's odd, because in a lot of contexts (hospitals, EMS, etc.), red outlets are used to denote outlets that are connected to battery/UPS, i.e. critical loads, versus the regular, which can be 'sacrificed' in an outage.


Plus there’s 240V in Paraguay. I travel with cheap universal adapters and never have any problems.


> The hacker in me hates it too but just imagine if a small portion of standard-looking outlets did not output 220V (or whatever standard you have) and say 330V.

Overvoltage is now routine in places where there's lots of PV installed in homes and not enough load nearby.

If you live in such a place, you have a deep appreciation of varistors and should have either good insurance or a little bit of soldering skills... preferably both.


> Overvoltage is now routine in places where there's lots of PV installed in homes and not enough load nearby.

Every solar inverter / microinverter manufactured in the past two decades (if not older) must monitor the grid voltage+frequency and disconnect if it falls outside of a certain tolerance. If things go out of tolerance there is a defined period of time where it must recover or the inverter is required to trip out. There are also hard safety limits that cannot be exceeded whatsoever. I am not aware of any conditions that would result in overvoltage.

In CA as of (IIRC) 2021 these systems must be hooked up to some kind of online monitoring so the utility can temporarily command them to exceed tolerances. If the grid is going unstable due to load the last thing you want is everyone's PV system tripping off making the supply situation worse. So the utility can inform the system to exceed the normally tight tolerances by a larger deviation. They can also command PVs systems to shut off but there are strict limits on how often and how long they can do that and it must be driven by grid stability needs.


Yes, absolutely, same here.

The problem is varistors blow out before the safety measures work. Perhaps due to wear or low quality, but this still happens.


I'm not sure how a single inverter failure could drive voltage high. Or how a varistor failure could cause a problem... The inverter has to perform a DC-AC conversion and has many more ways to fail safe than unsafe but I'm not saying it is impossible. I've seen some oddball things. But it certainly isn't a widespread issue.

Smart meters report voltage, the utilities would know if this was happening and given how much they hate rooftop solar they'd be yelling about it if they could.


> just imagine if a small portion of standard-looking outlets did not output 220V (or whatever standard you have) and say 330V.

Every once and a while an electrician wires up standard US outlets to 480v 3-phase instead of 208v 3-phase, so you end up with an outlet designed for 120v that puts out 277v.

Sometimes noone notices because the switching power supplies plugged into them are just fine with this.


From my experience appliances tolerate a wide range of voltages. The outlets in my house routinely deviate from the standard 230V, with the lowest I have seen at 170V and highest at about 260V. I have not had any appliance malfunction.

Edit: I am not advising anyone to deliberately do stupid things, simply mentioning that from my experience the builtin margin is fairly large.


You (or your landlord) should probably hire an electrician to get that checked out – especially the higher voltage might be indicative of some scarier failure modes.

A voltage drop of 25% could also mean you have semi-broken wiring somewhere, which can cause fires or shock hazards on faulty appliances.


My first guess would be something like a broken neutral wire, making the neutral voltage depend on the imbalance of the load between the AC phases. From the little I understand about it, you could have up to the phase to phase voltage between the broken neutral and one of the phases, with the voltage dynamically changing as devices are turned on or off. It's very confusing (since everything expects the neutral to be referenced to the earth, which is constant 0V by definition), and can burn up devices.


That definitely reads like somebody removed/forgot the neutral bond.

You're understanding is correct, if neutral is allowed to float it's voltage will depend on ratio of the load on the 2 phases.

It also creates a variety of hazardous conditions and opportunities to make spicy metal.

You can play with it here courtesy of Paul Falstad and Iain Sharp: https://tinyurl.com/yq4lukm6


I did but unfortunately it quickly turned into all parties involved blaming each other (it's your utility, it's your installation...) and it got nowhere. For the past year it's been much more stable than before so I don't worry too much about it.


I would not assume that this fault is not dangerous TBH. May well be a good idea to hassle them some more. If you're renting, you don't need to care who is at fault - your landlord needs to sort it. If you own, you may need a 3rd party electrician to settle the argument.


See above about a broken neutral. A broken neutral is bad. One could easily load a system or even just have wetter soil so that the voltages are well balanced for a while despite the neutral being open, but that doesn’t make it less bad.


Make sure you have good insurance and multiple loud smoke detectors...


Insurance won't cover if you knew there was a fault and didn't fix it!


Do you have a citation for that?


Sure. This is the relevant clause in my current home insurance policy:

"You must take steps to maintain the Home in a good state of repair and take all reasonable precautions to avoid loss, damage or injury and to safeguard all property insured from loss or damage."

These things are pretty standard - I would be very surprised if there isn't a similar clause in all of them.

Which implies that, if you fail to do so, they don't have to pay up.

The wording in your policy may be different. What are "reasonable steps" will depend on legal precedent. It may, for example, take into account that you're not an expert, and will probably include some reasonable time to get stuff fixed. But certainly it provides them the opportunity to deny a claim.

Obligatory disclaimer: I am not a lawyer or insurance expert, get your own advice if you need it.


It seems plausible that not addressing the electrical anomaly described by nicolaslem could be called a failure to maintain the home under your policy.

For completeness, the relevant section from my policy is "We will not pay for any loss to the property...as a result of...Neglect, meaning neglect of the insured to use all reasonable means to save and preserve the property at and after the time of a loss, or when property is endangered". But in the same context, it says "However, we will pay for any resulting loss from ... defect, weakness, inadequacy, fault, or unsoundness in ... design, specifications, workmanship, repair, construction, renovation, remodeling, grading or compaction; [or] maintenance."

It would be shaped by the legal precedent in interpreting these sorts of clauses, and perhaps also the whims of a jury. It still seems unlikely to me that either of our policies would end up excluding the electrical anomaly, and moreover I've yet to ever hear a verifiyable account of someone whose homeowners insurance claim was denied after an electrical problem in their house led to a loss.


I don't know if that exact case can be found, but it's a fairly obvious generalisation of the general principle. that if failure to repair in a timely way a fault or delapidation can result in reasonably forseeable further damage, insurers will be very reluctant to write policies cover the further damage; because it would result in moral hazard in the purchaser of insurance. So I would personally not like to rely on it being covered (apart from the obvious risk to the person of the house burning down).

That's not to say that the original electrical fault wouldn't be insured - that depends on other terms.

Your policy does seem to be more lenient than mine in that it allows "resulting loss from " ... "inadequacy or unsoundness in" ... "maintenance". I wonder what the scope of that is in reality.


Nobody can provide you with a citation because the specifics will be the wording that's in your individual policy.

But, generally, policies require you to maintain the property.


Dips and spikes are routine in electrical power delivery. In my experience, dips are much more likely to be the culprit of damaging equipment than spikes. People are used to protection from spikes with surge protectors, but the only thing that protects from dips is a UPS. I use a small UPS as part of my entertainment equipment. Not because I want to watch TV during an outage, but to keep from damaging the equipment with the power dips.


How would a power dip damage an appliance?


> How would a power dip damage an appliance?

For AC motors, the lower voltage might mean they do not have enough power to turn, so all the power they consume becomes heat in the motor windings (and since they're not turning, there's less cooling).

For electronic power supplies, they might either pull more current to maintain the same output (again leading to more heating), might output a lower voltage (and DC-DC converters which consume that voltage might in turn draw more current, again leading to more heating), or they might even misbehave and output an oscillating voltage; they might also detect the power dip and shut down, only to power up again moments later, repeatedly.

A device in an idle stand-by mode is probably the best case, since it's using little power from a supply sized for a much bigger load.

I disagree with the sibling comment that the only protection from voltage dips is a UPS or similar; a simpler protection is an undervoltage relay with a timer, to convert the voltage dip into a power outage (and also prevent the power from being restored too quickly).


* The only protection available as a consumer add-on.

Sure, if the manufacturer wants to increase the cost on the BOM for their PSUs, they can use additional components to survive dips, but who does that on disposable electronic equipment? Hell, even "expensive" TVs don't. I quote expensive since you can now get 65" 4K TVs cheaper than a mobile phone, but that's a tangent. So if you are wanting to protect your electronic equipment with another device readily available that is just plug an play ease of use with no knowledge of electronics, what do you suggest?


I have a friend who did that; he put one of these relays on the apartment's power panel, so the whole apartment was protected against voltage dips or too short outages. It might not be a common consumer item, but it's a readily available device, AFAIK commonly used to protect industrial motors.


common industrial does not come close to common consumers.

adding something to the power panel is not something a consumer can do. how is this even being confused?


It's not power dip, it's voltage dip. An appliance will often draw the same power at the lower voltage, so increase current, which can cause overheating and damage.


Typically in these dip situations, you can hear the PSUs being very unhappy about the situation. A cringe inducing high pitched squeal can be heard from any PSU that's doing work as they try to continue doing their job while in this undervolt condition.


If it's turned off or it is on and not being used, probably not much. But more and more equipment no longer has an off mode and is more of an idle stand-by mode, so current is still always being used by part of the system.

The point is that in electricity delivery, it is normal to have deviations in the voltage as acceptable. Most power supplies have tolerances that can handle these deviations. A dip is something outside of the deviations that most people don't consider as they are only focused on spikes and only use surge suppression devices. Since the only protection from dips is a more expensive battery solution, most people do not bother outside of computer related usages.


Ah, so e.g. something like a device flipping between “powered” and “not powered” states, which then wears out some part that doesn’t expect that state change to happen so often?


no, not quite. a dip is some lower than the accepted deviations from the expected value. if you have an accepted range of +/-10%, but the dip causes the voltage to drop 15%, that's a dip. some places define an outage as being less than 5% of expected value. so somewhere before outage, you have a severe undervolt situation where the equipment struggles. the longer the dip lasts, the worse things can get.

one of the shops that I worked at suffered a catastrophic situation when a nearby construction crew cut one phase of the 3-phase power coming into our facility. the poor transformer died, and took out the some of the more delicate PSUs attached to some very expensive equipment. we were down for weeks recovering from that.


Most of them are either 110-240V appliances, or lose performance when it goes around 170, and you may not notice.

260V is in +/- 10% threshold and is possibly falls within "engineered in tolerance" range, but will probably shorten the life of many appliances if supplied constantly.


Lots of devices have switched mode power supplies that will still output the same voltage. Last time I had a brownout the only thing that stopped working was the washing machine, and I thought that was broken.

Paradoxically, it may be the lower voltages that are more dangerous, because it will result in a higher current draw from all the devices.

Mains voltage has a nontrivial allowed range (in fact in Europe they increased it slightly so that devices would work across countries with slightly different original standards) but this is well out of spec.


Are you measuring RMS voltage or just the instantaneous voltage?

An RMS voltage of 230V corresponds with a peak voltage of ~325V so reading of 260V could theoretically happen.


That's the reading from my UPS, I believe it's RMS since it reads 234 V currently.


That's not how it works. For a sine wave the integral converts to Vpeak/Sqrt(2)


Anything with an AC/DC transformation would be fine, anything with an AC motor would be not. Partially, not the every compressor in a refrigerator would tolerate that.

But 170V... yikes!


Thats quite a spread. Is it up to spec where you are?. In Australia we have 230V nominal, but the allowed range is from 216 (-6%) to 254 (+10%).


> pushes me to support mandatory certification

It wasn't mandatory but this is one of the main reasons Underwriter's Laboratory was started. The market needed a certification to say "yes, this things does what it's says it does and in a safe manner".

My dad owned a retail store in the 1970s and he distinctly remember being told "Lots of retailers won't carry a brand/item unless it has the 'UL' sticker on it."

https://en.wikipedia.org/wiki/UL_(safety_organization)


You can find many fake "UL certified" products on Amazon, with a counterfeit UL logo and all. I think the problem is companies like Amazon not being held liable for what they sell.


Would this be comparable to a CE marking in Europe or more like a TÜV certification?


Sort of. UL and CE are certifications that declare a a product confirms to the standards defined by those groups. The main difference is that UL only focuses on product safety (i.e. Shock and mechanical hazards), while CE covers product safety plus environmental and health requirements.

UL is technically a global standard, but mostly used in USA/Canada. That's only two countries which already have laws governing what can and cannot be put in a consumer device.

I'm not as familiar with the history of CE, so I don't know why CE decided to cover environmental standards. But my speculation is that it's because CE covers ~30 countries with a larger range of laws.


These days, any thing can have any sticker.


Specially TÜV. Means near nothing.


Decent chance there is a little ul logo on the cat water fountain.


It's got a CE mark, but it's unclear if it's valid or not. This is a mandatory certification in the EU, like the UL listing in the US.

The device is specifying the output voltage, which isn't in spec for the connector, but it is (apparently) accurate.


There's a deceptively similar mark that stands for China Export and does not indicate EU certification[0].

[0]https://www.kimuagroup.com/news/differences-between-ce-and-c...


For context, this isn't an official mark created by China or any other entity.

It's just some fraudulent manufactures that are using a paper-thin excuse to illegally apply a fake CE mark.


Looks like CE to me: https://u.ale.sh/iaN5ie.png

It is a self-certification mark though so ¯\_(ツ)_/¯


Wow, that's incredibly close. I assumed there would be a public database of CE (European) approved devices or manufacturers, but I can't find one from a quick search.


The CE marking is a self certification program, and there isn't an approval process. All the can happen is that you can get fined after the fact for applying the mark to products which don't fulfil the necessary requirements.


Technically it is a self-certification program, since it's the device manufacturer who signs the certificate, but that's not the whole truth. A manufacturer still needs to prove compliance (in the case of the EMC directive, either Annex II or III) or slapping on the mark is just fraud.


CE mark (the real one) is self certified


There is no such thing as a “China Export” mark. No products has been shown to have it. It’s a fake urban legend: <https://en.wikipedia.org/w/index.php?title=CE_marking&oldid=...>


That's so interesting.

I've just done a quick dive into my electronics. I have a Tonbux power strip where the C and E are definitely too close together.

Edit:The website I linked is a Chinese manufacturer. If it was an urban legend, it seems to be being treated as fact in a way that matters now.


> I have a Tonbux power strip where the C and E are definitely too close together.

As per Wikipedia, quoting the European Commission, people displaying the CE logo with incorrect dimensions exist. This does not prove the legend.

> Edit:The website I linked is a Chinese manufacturer. If it was an urban legend, it seems to be being treated as fact in a way that matters now.

Please stop spreading urban legends on the basis that other people believe in them.


I'm not interested in arguing you out of your surety. I do want to note that I believe that when an urban legend is implemented in reality, it is no longer a legend. And you aren't going to argue me out of expressing my opinion.


> when an urban legend is implemented in reality

But you have presented no proof of that. What has been shown so far is that:

• One Chinese web site presents the information as factual, i.e. a simple retelling of the legend.

• Equipment exists which have the wrong dimensions on the CE logo.

What you have not proven (and neither has anyone else) is that some manufacturer has actually used the faulty CE dimensions to try to claim that they weren’t trying to show a CE mark, but instead this mythical “China Export” mark. Note that for the legend to work, it has to be some sort of benefit for the manufacturer, namely that they must be able to get out of being accused of falsely displaying a CE mark by, when accused, instead claiming that the CE mark is not in fact a CE mark. But this must be claimed publically by the manufacturer. Surely someone should have some example of this happening by now?


UL isn't actually mandatory in the US. The only thing mandatory that I am aware of is FCC certification for devices with signals over a certain number of Hz, and they wouldn't care about a USB port being abused.


I read somewhere, that there's no such thing as a UL-approved turkey fryer.

https://www.ul.com/news/put-safety-menu-thanksgiving

I think that is still the case.


Every turkey frier I've ever seen is a propane burner and a well sized pot to put on top of it. 0 electronics unless they have a thermostat type feature (which I've never seen).


I’m pretty sure UL applies their testing to anything with safety ramifications.


Gotcha, I thought it was just an electrical certification. However if they won't certify a propane burner and a pot just because it's labeled 'turkey frier'... i'm not sure how they can certify any gas grill, gas range or propane burner of any kind.


Has to do with the large amounts of flammable oil that inevitably spill out.

Some years ago, I saw a video, done by Consumer Reports, I think, that showed a fireman, in full heat gear, using a turkey fryer, and showing how incredibly easy it is to spill oil.

Every Thanksgiving, there are always quite a few turkey fryer accidents.


Yes. This is because people do stupid shit.

1) they overfill the pot, even though every frier I have ever purchased comes with a table of turkey weight to oil (not perfect obv but generally they are conservative, at worst you must add a little oil once the bird is in the frier). Sometimes this table is literally etched into the pot. Failure here will overflow the oil and send it into the burner causing a fire, once that fire reaches the inside of the pot .. yaknow, not great.

2) they don't sufficiently dry the bird or even worse put it in frozen. The previous causes potential spatter that could 'boil over' and cause fire. The later i've seen some videos of .. much less great.

Let's be clear, you can do exactly this stupid shit deep frying something on your stovestop, at least with a turkey frier you can be outside away from flammable things.

It's pretty easy to deep fry a turkey safely and in fact every year I probably fry between 10-15 birds (I love turkey). On thanksgiving I generally end up frying 5-7 birds for my family and some of the neighbors who either are to scared or just don't want to buy a setup, either way I'm happy to do it for them.

1) make sure your oil level is right according to the pots instruction.

2) make sure your bird is thawed and pat it dry inside and out

3) heat the oil on the burner, but move the pot off the burner before inserting the turkey, also remove the pot before removing the turkey.

4) watch your temperatures and keep the lid on.


I recently ran into this buying an EVSE to charge my car. Amazon in the US is full of imports from generic Chinese brands that are half the price of name brands but not UL certified. Many of them say "UL certified cable" which doesn't tell you anything about the entire charging unit, just the wire stock they used.

It's all fraud. And at 40 amps, potentially quite dangerous.


Good luck filing an insurance claim for damage caused by the use of a non-UL-listed appliance.


What language in an insurance policy requires the use of UL-listed appliances for coverage?


None.

Stuff like the post you are replying to is common "good luck with insurance" trope. Insurance protects you from stupidity, errors, and negligence. It doesn't protect you from fraud or intentional malice, but using an uncertified device is not fraud.

Note that after an accident related to personal stupidity or error, an insurance company could decide you are too risky to further insure, or that the cost for your insurance should increase dramatically. But they can't deny a claim.

All of this is of course a significant summary, but insurance won't (can't?) deny a claim linked to an uncertified electrical device in normal circumstances.


I used to work for a major clothing retailer. Our insurance policies did require us to use UL certified appliances in our stores.


Did you read the policy, or is this what somebody told you?


The head of store told me it was the policy because of insurance requirements we were looking at buying a paneled LED display/wall and UL vs Non-Certified was a large price difference. In the end we paid for UL. (They were actually probably identical panels, non-cert was from china, UL was from a us supplier)



Some devices do require a NRTL (nationally recognized testing laboratory) mark. That could mean UL or TUV or whatever. NFPA 70 will refer to “listed” or “recognized” devices in such cases.


Anyone can stick a CE sticker onto their products. It's a self certification mark, and I've never heard of a company ever getting in trouble over this stuff. All it says is "I promise to follow the CE rules" but there are no mandatory audits or anything, unless a company gets found out to be violating the spec.

I don't think the CE mark protects consumers the way it could decades ago, with international imports taking a few seconds and free postage to boot.


Fair point, but given that some manufacturers have no problem at all to just blatantly use brand names without permission, having a CE mark is unfortunately not a sure sign that a device has ever been inside a certification lab…


The device is specifying the output voltage, in very black, very tiny letters. How convenient. The person who took this almost impossible photograph should get a Pulitzer. No quantitative measurement for the real voltage, or current for that matter.

https://donglec.com/blogs/journal/are-third-party-chargers-h...


It's mandatory to have the CE mark.

It's a self-certification. You can decide how much that's actually worth for non-EU vendors.


This.

Nintendo comes to mind; charging the Switch (the earlier models IIRC) with a third-party adapter was a lottery, and the losing prize was a fried console.

They've been guilty of this practice for as long as they've been making electronics - I think it was the NES or the SNES that used a standard barrel jack and voltage, but reversed the polarity, with no circuit to protect the console.

Also - using Ethernet ports/cables for serial console access is not even evil, it's just stupid. Granted the switches/routers that do this are not exactly SOHO equipment, but you need to let students in a lab near that, and it's just asking for trouble.


> They've been guilty of this practice for as long as they've been making electronics - I think it was the NES or the SNES that used a standard barrel jack and voltage, but reversed the polarity, with no circuit to protect the console.

Is there actually a standard about that? IIRC, recently things have drifted towards "center positive" as customary, but most adapters and devices have the little diagram about how they're wired for a reason.


I think everything I've seen that sony makes is centre negative. For their consoles, this only mattered for the psone and slim ps2.

Always seemed dumb to me, since you'd want the "ground" side to make contact first when inserting.


Audio and audio adjacent gear is nearly all center negative. Everything else is probably center positive, but you still have to check. No standards.


> Nintendo comes to mind; charging the Switch (the earlier models IIRC) with a third-party adapter was a lottery, and the losing prize was a fried console.

The problem you're thinking of was caused by a Nyko third-party docking station with a faulty hardware implementation of USB-PD. While Nintendo's software implementation of USB-PD was flawed in some ways, it didn't cause this problem.

> I think it was the NES or the SNES that used a standard barrel jack and voltage, but reversed the polarity, with no circuit to protect the console

There is, sadly, no "standard" polarity for barrel power jacks. Center-positive and center-negative are both fairly common.


> While Nintendo's software implementation of USB-PD was flawed in some ways, it didn't cause this problem.

I stand corrected.

The dock however, still rejects non-Nintendo chargers. I have an MBP, a Thinkpad, an iPad, and a Switch - every device works with each other's (and third-party) chargers, except the Switch, when docked.


I think these usb-c pd (and other) issues were corrected in the oled switches and the docks that come with them but the fixes might not have been total.

This comment, specifically about some of the technical details of the video out stuff points to at least some changes were done in the new generation: https://www.reddit.com/r/UsbCHardware/comments/171c3mj/comme...

Someone can correct me on this as well. I've noticed that my switch will charge properly and quickly on their provided charger and a few other usb-c chargers I have but not certain other ones where it charges much slower. My theory has been that not all usb-c chargers are compatible with all voltages and that perhaps the switch's 'preferred fast-charge voltage' is somewhat uncommon (i think it's 17v?). Can anyone confirm this is how these things work? I just assume there is a negotiation where the charger says 'I can supply these voltages, and perhaps at these max amps, and the device choses one or none of them depending on it's needs.


> I think these usb-c pd (and other) issues were corrected in the oled switches and the docks that come with them but the fixes might not have been total.

I have the OLED model, and the accompanying dock refuses every single non-Nintendo charger I've tried. It literally tells me so on the screen.

> My theory has been that not all usb-c chargers are compatible with all voltages [...].

Correct. Both devices present eachother with a list of supported modes, and negotiate the optimal one. If you try a fancy charger/powerbank with a screen, it will even present per-port current/voltage stats. Fun to observe the changing power draw on different devices.

Also if you plug another device to the same charger, it will trigger a re-negotiation, possibly end up in a different mode. LTT had a whole video on modding ancient consoles to use USB-PD, and the possible resulting issues.

https://linustechtips.com/topic/1470228-how-to-put-usb-c-pow...


Turns out I seem to be right about the negotiation: https://acroname.com/sites/default/files/shared/blog-basic-p...


OTOH we have tons of crazy non-usb transformers with all kinds of different plugs that might or might not plug into devices they're meant for.

It seems like somehow we're used to the idea that this particular plug will only work with the device that came with it, but we assume that USB-A is USB-A. I know I do.

This does make me wonder about the USB adapter I got with my dash cam. The documentation says all over the place to pretty please with sugar on top use our adapter. I'll have to stick a meter on it. [Edit: 5.1v.]


It's likely that they are trying to avoid support calls from users plugging into whatever USB port is on their dash that might not supply enough current, or is intended for media/AA/Carplay and forcing the camera into interfacing with the infotainment system.


It's not just USB-A. You can assume your US-style wall outlet is ~115 V, 60 Hz. Cigarette lighters in cars are 12-ish V.


> The hacker in me hates the idea of enforcing something like this

As long as you are free to modify the hardware or purchase specific non-conforming hardware I see no reason why this would be painful for a hacker.


I don't see how making sure that when something looks and quacks like a duck is actually a duck conflicts with the hacker ethos. The more standardized things are - the easier it is to build something. I love that I can take any combination of DIN parts and suppliers and know they will play nicely. Also there are a lot of standardized higher voltage connectors. this case is incompetence or negligence from manufacturer - and those are against everything hacking is about


> The hacker in me hates the idea of enforcing something like this, but poor interoperability is such a pain that it would be nice to have stronger guarantees.

For pure consumer products (whatever that means) safety standards are quite reasonable. There are already legal requirements in the USA that plugs have certain shapes controlling orientation, grounding, and expected voltage, as well as building code so that people don’t trip over long power cables. Food safety means you can pick up something at the shop and have some faith it won’t kill you.

This reduces cognitive overhead and doesn’t require you to be an expert in every domain.

It also doesn’t stop you from hacking your own stuff (mostly — please don’t mix ammonia and bleach!) and easily provides you a bunch of dependable items on which you can build your hacks. So you can (briefly!) supply 100 amps of 240V AC over USB A at home if you want, you just can’t sell it. You can make yoghurt at home and store it on the counter in the sun if you want, no problem.


> mandatory certification (enforced by patents/other IP protections)

> The hacker in me hates the idea

If the hacker in you really hates this, then why insist on enforcing via means that restrict both vendor and user freedom (IP) instead of regulatory enforcement that exclusively targets vendors & leaves hackers free to hack?


What would the regulatory enforcement look like?

If I develop a new connector, how do I get the regulator to start enforcing that everyone who uses it is following my standard?

What happens when I find a way to extend the specification in a safe, backwards compatible manner, but this conflicts with the standard as enforced by the regulator?

I’m not saying that these are insurmountable problems, but I feel like the regulator should focus on issues such as safety, and interoperability should be enforced by the company/consortium that develops the standard in the first place.


Hackers want not just hack for themselves but share the product of their craft with other parties without going through fences.


Some do. Some don’t. The various uses of the term “hacking” do not universally require tech to be shared.

Long before RMS and other ideology-oriented types, people were adapting commercial tech to local purposes which the vendor didn’t intend and wouldn’t endorse.


Are you implying that regulation need put up more such fences than IP restrictions?


I think the thing that would let me stomach it is 1. Only legally mandating it for consumer devices / sold on the open market / commercial entities manufacturing it, or whatever the sensible way to structure that sentiment is, and 2. USB supports negotiating higher power settings, so you're not artificially limiting what's possible, just enforcing a safe worst case. If you need some USB connector that carries a kW you can theoretically still do that, you just have to not default to putting 100+ volts across the power pins the moment the thing is plugged in.


Re: 2: as you likely already know, this is a (major, pretty well thought out) part of newer usb standards. Unfortunately there’s no realistic way to backport this to older usb accessories. You can’t push an OTA update to the author’s wall wart.


I thought it worked fine with devices that had never been updated because you start from the very oldest spec and the lowest power and then both devices have to negotiate up?

I mean, sure you won't get better performance or power out of an old device but it's at least safe which is good enough for me, and for bonus points it's likely to work at some reduced level.


Yup, that's how it works, but you unfortunately can't retrofit out-of-spec devices like the author's to be within spec at scale.


Yes, mandating this on consumer devices is quite sensible.

At least adhere to the spec to such a level that it won't destroy other hardware.


Could that ever really help? The vast majority of devices do this correctly, even from the cheap, nameless manufacturers cranking stuff out for sale in marginal retail outlets. I suspect even if there was some sort of legislation or accountability that this particular culprit would have pulled the same stunt. They'd have relied on the fact that it's difficult to track down who manufactured the item, that there'd be little incentive to do so by anyone who became aware of it, and that they'd be safe from repercussions across some international border.

I think your initial instinct is right.


> The hacker in me hates the idea of enforcing something like this

Why? I'm not sure what being a hacker has to do with it, but this sort of thing would benefit everybody and harm nobody except for the negligent.


Why not have efficient law and just sue large sums out of misbehaving manufacturers? Then you no longer punish the innocent.


If you can get a hold of the manufacturer, sure. But don’t count on Amazon or other marketplaces helping you with that: They’re not a reseller, as they’ll be happy to tell you; no liability! (And no responsibility for collecting customs payments either.)


Make Amazon sign up for compulsory customer protection insurance if they want to share the liability with somebody, otherwise it's all theirs.


I'd rather see specific laws against bad voltages on USB.

Isn't there already some law somewhere against things that are so obviously not what a consumer would expect?


That CE marking on the adapter is probably fake - how would it have passed certification while outputting a voltage 50% higher than spec?


All the CE marking indicates is that the product complies with European specifications. As far as I know, there are no EU/EEA specifications regarding the voltage of an USB port.

This may violate the USB spec and burn out phones, but it's not necessarily undeserving of the CE mark.


Turns out the new regulation for chargers and USB-C universal compatibility actually demands USB Power Delivery [1] support, but I guess it's too early to expect compliance with that.

Even without that, one would hope that part of the compliance tests includes actual compliance with whatever port specification is being used - I don't think any part of the USB spec allows for 7.5V, but I might be wrong. You just wouldn't expect, say, a portable battery to have a standard Schuko plug but output 330V while bearing the CE mark.

[1] https://eur-lex.europa.eu/legal-content/EN/TXT/HTML/?uri=CEL...


I quote from the regulation you linked:

> The requirements set out in points 2 and 3 of this Part shall apply to the following categories or classes of radio equipment:

> 1.1. handheld mobile phones;

> 1.2. tablets;

> 1.3. digital cameras;

> 1.4. headphones;

> 1.5. headsets;

> 1.6. handheld videogame consoles;

> 1.7. portable speakers;

> 1.8. e-readers;

> 1.9. keyboards;

> 1.10. mice;

> 1.11. portable navigation systems;

> 1.12. earbuds;

> 1.13. laptops.

Unless you can convince your local standards authority that the cat water fountain you bought is actually a weird looking portable speaker, I don't think this law applies her.

Unfortunate, really, because USB port really shouldn't use non-standard voltages. I'm sure there's some consumer protection law you could use in court to make the manufacturer pay for damage if they damaged your devices (there are a bunch of "a product should work like you would expect" types of laws sprinkled across consumer protection laws) but I don't think this violates CE standards.


USB does control use of their marks, it would probably be new law to prevent use of the physical arrangement.


> new law to prevent use of the physical arrangement

Even if the connector itself were patented?


It’s difficult enough to figure out which side goes up. I can’t worry about this as well.


Mandatory how? Won't they just ship an uncertified adapter anyway?


Patent the connector and enforce it aggressively.


This brought back a distant memory of when I bricked my very first MP3 player, a Rio 500. See when Rio 500 was being designed the mini-usb B spec was not finalized yet, so when it was released it came with what looked like a normal mini-usb cable for charging, but in fact the pin-out was different. At some point I tried plugging it in with post 2000 cable and it killed the device.


IIRC, just before "miniB" actually hit; there was a lot of confusion and efforts to make something like it. Olympus and Fuji both had a USBC looking wingless connector on some USB cables, they'd used the same connector, but wired it differently.

I was selling cables and adapters on ebay at the time and we had a package with both types. Easier to sell people both versions than deal with "oops i needed the other one."

(I may well have mis-named the parties; apologies if so)


To be completely fair, those power banks should have a diode (or some protection circuitry) to prevent their damage. A loose cable could easily put higher voltage on the port than 5.25V.

That said, what an awful USB port to come across. A little reading wouldn't have gone amiss though. My natural reaction would have been to assume it was an output, not an input.


A diode doesn’t protect from over-voltage; that requires more complicated circuitry as far as I understand.

And how would a loose cable cause a voltage spike?


TVS diodes can protect from transient voltage spikes when used properly (low impedance to the input connector, properly chosen and with the proper supporting circuitry)

Zener diodes can temporarily protect an overvoltage too but you will need something to take all that current that is now going through it, making it pretty hot and likely to fry something

You can pair something like this with a positive temperature coefficient thermistor to act as a fuse (as it gets hotter the resistance goes up).

These circuits are tricky to tune right, take up space and can add significant cost to a product. So with a drive in consumer products to lower cost smaller things you may not see them everywhere.


perhaps a they meant a zener diode, which can be used to clamp a voltage? The downside being that it dissipates the excess energy across it's self.

> how would a loose cable cause a voltage spike?

From the top of my flu-y head, connecting and disconnecting an inductive load (like a motor) can cause spikes. However in USB land, that's pretty rare.

dc-dc step up devices use an oscillator to charge and discharge an inductor to achieve a certain voltage increase. They _could_ be noisy when starting up, or have transient load.


> perhaps a they meant a zener diode, which can be used to clamp a voltage? The downside being that it dissipates the excess energy across it's self.

Maybe in conjunction with a self-reset polyfuse - buys just enough time to trip the fuse.

> From the top of my flu-y head, connecting and disconnecting an inductive load (like a motor) can cause spikes. However in USB land, that's pretty rare.

Exactly - and it's not all that rare. A USB fan, a spinning disk drive, etc. In the right condition even a capacitor can be a problem (difficult to simulate, but it can become a short-term battery cell).


ThermoWorks SmokeX and Signal both use a 12v usbc power adapter. My partner fried her phone on it once due to seeing the cable and assuming it was a normal charger.


I thought my ThermoWorks Signal had a dead/defective battery after trying to charge it on a standard USB power adapter. Device booted up and and functioned fine, except the battery wouldn't charge. Plugged it into the provided adapter and it started charging again.

Thanks for the PSA, I'll be sure to get that adapter off my kitchen counter right away!


I too have tried to use a USB power bank as a kind of DIY UPS to power a Raspberry Pi SBC. What I learned - which may be unrelated to your experience - is that all of the several power banks I tried can be either charging, or powering a device, but not both at the same time. So my Raspberry Pi would run until the power bank got low, then the power bank would cut power to the Pi and charge itself, then power the Raspberry Pi up again. I had to buy a power bank specifically advertised as a USB UPS; that worked fine. The normal power bank seems to be designed to charge a battery powered device like a mobile phone (whose own battery can be thought of as a kind of UPS for the device), but not a device that requires continuous power (like the Pi).


Which one did you get? I got a Zendure specifically for this purpose, but I find it the hard way that when it switch between battery power to wall power, it will momentarily lose power for a sec, resulting in a reboot


I wouldn't trust the writing on it; either.


I recently found a Huawei-branded power bank that outputs 9V over USB-A. See https://www.aliexpress.com/item/4000209696496.html and look at the label on the seventh picture.

EDIT: I may be wrong. Apparently this is now allowed by the Quick Charge spec. See comments below.


That looks like a proprietary version of Quick Charge, which has a negotiation step before the alternate voltage is enabled. From that murky period where everyone was tacking on all sorts of protocols to get more than 5V/0.5A from a USB-A port.


That might be within some quickcharge specs and it won't output 9v by default


Yes, I can confirm those are standard quickcharge specs.


Yes, it's clearly marked as 5v/9v, so it is capable of 9V, not the only one voltage.


At 7.5V, any properly engineered consumer device you plug into that port should do one of two things:

1. just accept the 7.5V and charge happily.

2. trip overvoltage protection and refuse the charger.

That doesn't make this okay, it just means it isn't catastrophic.

Note that I said consumer device. If I plugged one of my microcontroller dev kits into this thing, the magic smoke would be released pretty quickly.


> Yes, properly implemented USB type C ports can negotiate all sorts of voltages, but this is not one of them.

Not just USB-C... even early generation QuickCharge could (https://en.wikipedia.org/wiki/Quick_Charge).


I noticed something similar to this on my Insta360 ONE X charger. Initially I thought I could just use any USB power adapter but after many tries it turned out that the vendor implemented their own voltage on their charger sold separately. Quite a disappointment as charger broke after two years.


For what it's worth, I can charge my X3 (same camera, two generations later) with all the USB-C charger I tried (laptop charger, phone charger, car adapter). USB-C helps, I guess (One X is micro-usb).


Few years ago I bought a 12V led strip from aliexpress, it came with a usb charger. A "12V" USB charger. You can easily guess who put it near other chargers by mistake and then fried a PS4 controller trying to charge it with that :/


Everything old is new again. I used to think that the Etherkiller was a joke... http://www.fiftythree.org/etherkiller/


I just bought a cheap oscilloscope (Hanmatek DOS1102) and it has the opposite oddity. It comes with a standard 5v USB adapter, but the cable going to scope is a USB A on one end and on the other... 2.5mm X 2.1mm barrel! Why they did not use a standard USB Micro or Mini (or C) connector on the scope, I'll never know.


I recently replaced my 120V receptacles with USB ones. Super convenient and it's allowed me to get rid of the dozens of various transformer plugs around the home.

https://store.leviton.com/collections/usb-outlets


While I think this is a great idea, I've seen these in public places and the USB-A sockets almost always get damaged. I'd be worried about having to replace a $40-50 receptacle every year or two if I happened to bump the cable and wanted to keep using the USB part. Still a good idea overall and I can see them being used in a few places around my home to save space.

Also, I'd love to see ones with 65w charging so I can charge my laptop and still have an outlet to use!


How about 60w?

https://a.co/d/eBLEVjC

There are a few no-name brands with 65w, but I don’t trust them.

Just note, they are much larger than normal outlets and can be a squeeze to fit in a normal box.


Wow, I appreciate the warning. I have a similar fountain that also uses a 7.5 V "USB" connector, and that adapter definitely would've ended up in my big box o' orphaned USB bricks when the fountain inevitably gives up the ghost or just becomes too gross to keep clean.


I also applaud who ever came up with 2 strand wire with USB-A at other end and USB-C at other...


Seems pretty secure to me.


That previous thread the other day made me wish there was a cheap usb pluggable to tell you about the quality (and quantity) of voltage from a usb device.

Simple small screen or just led lights.

Maybe even a "kill-a-watt" for usb power cube/banks.


The tools exist, but maybe not in a single nice package. I use:

- A pass-thru USB power meter. Measures volts, amps, wattage (simple arithmetic), and watt-hours

- a USB load device. You can configure the voltage and amps to draw. Used in conjunction with the above, you can see just how much a USB supply can supply

- a watch cell powered cable tester. Not essential for your use-case, but great for working out whether a cable is at fault or not.

None of this directly measures quality, but usually you can infer that from amps, and from negotiation.


Would have been nice if he actually measured the output to verify. Takes 2 seconds with a multimeter. If the adapter is already out of spec, there's no reason why you should trust what is written on the side of the box.


Very valid point, I just did that and my multimeter measures the output at 7.71V.


I have the same fountain, I saw that when unboxing and immediately labeled the adapter as "FOUNTAIN ONLY". Really don't want some device fried because it received 50% more voltage than anticipated.


Same discussion about USB-C, Thunderbolt, etc and how users would be confused.


Not victim blaming here, but I always check the output specs on any power adapter I have before using it, especially USB. I have quite the collection and in the very least the amperage varies wildly.


I can only hope the person who designed this USB power adapter will end up frying their phone, tablet or other electronic device with it for some karmic justice.


I dread to think what the insides of that adapter look like.


My recent work experience leads me to believe CE approval is a rubber stamp. I don't have any clue what that certification is worth to anyone.


CE approval is not only a rubber stamp, it's a rubber stamp you get to apply yourself. By applying the CE mark you a certifying that your product fulfils all the necessary requirements and that you can document it, but no one will actually check. While it is illegal to apply the CE mark to a non-conforming product (or to sell or import non-conforming products with the CE mark), basically nobody gets prosecuted.


Firstly, CE is not a certification, it just means that the product is in compliance with legislation. It's something the companies need to verify themselves.

That leads to the problem child which is China and its lacking morals. Chinese companies will just slap the CE on anything, because the EU say that must and Europeans seems to enjoy seeing it. Sometimes, they will slap on a different CE marking, meaning "China Export". You can tell the difference by tracing the C to a full circle, if that hits the E exactly, its CE as in "conformité européenne", if it doesn't, it's China Export.

If you're a fly by night USB charger manufacturer, you just invent a new brand for next month, so you won't get the fines or be banned.


The mark people claim means China Export is just a fake CE mark.


I've understood the CE marking to mean that according to the manufacturer, the device shouldn't catch fire, shouldn't shock me, and shouldn't give off a lot of radio interference.

Never did I thank that would be some kind of "this is a great thing" approval stamp.

However, it never occurred to me that a USB-A charging brick would be able to give 7.5V, or even 9V or 12V as others have commented. That might completely fry some devices...


Self-attestation is introduced when the industry complains that having a 3rd party verify is too onerous and could hurt business. And they're not wrong, but the result is companies rubber stamp their own compliance. You see it a lot in DoD compliance now, for example.


Super dangerous, if someone were to not know and plug this charger into a regular USB device.


Isn't this just a lesson to always read the output values on adapters?


Hi, author here. If the writing on those adapters was easily readable by the visually impaired and surrounded by bright red/orange colors, this wouldn't be that much of an issue. I had one hell of a time trying to even photograph the output voltage etching specified on the adapter itself.


The info is still there.. You were not being lied to.


It's a USB port. Differently than the dozens of proprietary charging connectors that were ubiquitous before micro-USB and USB-C dominated, consumers have an expectation that it adheres to the specification.

To be on the safe side, one would actually have to check the voltage. Both the output voltage and whether these are really 0V and 5V to ground. The output frequency spectrum should also be checked.


To be honest, we used to have those round connecters that would vary in voltage a lot more, so I always check the adapters sticker.


Well, USB is a standard - you would expect a standard USB output to deliver a standard voltage.


Interestingly, even Samsung phone chargers put out 9v, but I think they only do that when connected to a Samsung device. On the plug is says 5v and 9v, and (I'm assuming) they switch to 9v when they detect a device that can use it for fast charging.


It’s called QuickCharge and was a standardized version of Apple’s fast charging or USB C PD many years before USB C was a thing. Samsung was a key player.

The charger emits 5V unless the device supports higher voltage and negotiates it.


after reading the title I thought the manufacturer coated the adapter in chilly, so cats won't chew on it and thought - "That's a brilliant idea".


> At one point I wanted to see if I could create a sort of a DIY UPS for the water fountain. It would be quite bad if I was at work and a power outage results in cats not being able to drink water (they don’t really care for normal water bowls after getting the fountain).

So another self-made problem then.


No, the point is that the charger has a standard USB-A socket, but delivers nonstandard charge. This is potentially dangerous, as the function of the charger does not match the user expectation.


Nope, the point is that he thought to fancy / easy up life with more tech (mentioned potential health issues my ass, you have to clean up every day anyway after pets - does he thin a fountain does not build up residue and germs?), and promptly got more issues to solve. One is the non-standard voltage output, another is spoiled cats which can't be arsed to drink from a peasant's bowl (knew about such habits before, exact same situation).

Stop trying to 'improve' life by more & more tech-based BS.


No, that's not the point. The point is to illustrate that products defy expectations with regards to the U in USB, which is for Universal. The rest of the article is context for the point, not the point itself.

Reason 1 supporting this: the article's title is "My cat water fountain comes with a spicy USB power adapter". What sticks out most here is the word spicy, and when used in conjunction with electricity, it usually means more electricity than needed. Very good title.

Reason 2 supporting this: The heading is "It turns out that you can’t trust any USB type A power adapter to be within spec". Nothing about cat fountains.

Reason 3 supporting this: the article is tagged with the "ramblings" tag, setting us up that the article will be opinionated, and not strictly just about the central point of it.

>Stop trying to 'improve' life by more & more tech-based BS.

Hard disagree. There's no clear healthy cutoff with regards to technology, and the frame of reference also changes over time (and the course of history). Our life is supported by a ton of technology, many pieces of it being thought about as both "too much" and "not good enough".


Hi, author here.

Usually I'd agree with you here, people use tech in places where it shouldn't be used quite often, but in this case I do not mind it at all. If this helps avoid future visits to the vet (and so far it has worked), then it's OK in my book.

And yes, you do have to clean it regularly and change the filters, we're already doing that.




Guidelines | FAQ | Lists | API | Security | Legal | Apply to YC | Contact

Search: